+7 (499) 951-79-41

+7 (499) 649-00-41

120 (8th floor), 6

Bratislavskaya Street, 109341 Moscow

mon - fri 9 am - 6 pm

All materials are property of their owner, and are protected by the law of the Russian Federation "On Copyright and Related Rights". Using text and photos without written permission forbidden.

© LLC, TD Plastmass Group 2019

INN 7723909200

KPP 772301001

BASE TYPE
ZX-530

Made for rough

envoirments

ZEDEX-530 (ZX-530) - is a synthetic thermoplastic composite material based on polyster (PPS).

ZX-530 is designed to work in the conditions of aggressive environments, it is resistant to many chemical substances and can replace ceramics and PTFE in sliding units, it significantly exceeds them in characteristics. The application of this material is effective where PTFE or bronze plain bearings cannot bear a longtime load. ZX-530 polymer is often used in spray booths - in their sliding parts, pumps, lines of electrochemical facing, the equipment of oil and gas and chemical industries.

FEATURES

  • High wear resistance

  • Quite low friction coefficient (0.07)

  • High chemical resistance

  • Easily processed by cutting and welding. Good machinability

  • Physiologically harmless. Suitable for contact with food products. FDA compliant

  • High precision in the manufacture of parts

  • Hydrolysis resistance

CHARACTERISTICS

  • Working temperature: -100°C to +240°C (+260°C)

  • Surface pressure (p): max. 25 (74) MPa

  • Sliding speed (v): max. 300 m/min

  • Fatigue (S): tensile fatigue strength at 20 °C and 1E06 stress cycles, 1 Hz = 40 MPa

  • UV-radiation resistance. Gamma-radiation: Limit absorbed dose 1000 kGy

  • Water: max. water absorption: 0,01 %, up to max. +140 °C resistant

  • Fire behavior: Oxygen index (LOI): 47 %, Classification: V-0 (UL94). Fireproof.

ADVANTAGES

The strength of ZX-530 in compression at +200°C is 16 times higher, the durability is 300 times longer than that of standard PTFE (polytetrafluoroethylene, teflon, ftoroplast-4).

The advantages of ZX-530 over PTFE (PTFE) and its modifications (F4K20, etc.):

  • High mechanical strength with gradation of temperature up to 250° Celsius

  • Low tendency to creep in the process of compressive loads

  • High wear resistance in a tribological use

  • Permissible pv-value is higher in dry running operation

  • Best assurance of exactly specified accuracy and less coefficient of thermal expansion

  • Minimum manufacture cost of ZX-530 parts by welding or injection molding

The advantages of ZX-530 polymers over ceramics:

  • Higher tensile and impact strength;

  • Non-sensitive to the edge pressure in the case of a mechanical load;

  • Greater resistance to chemicals;

  • Better machinability and mountability;

  • Wide dimension and product range of blanks;

  • Basic details made of ZX-530 are much more economical than those of ceramics or PTFE.

SUPPLY

Rods (diameter 6÷210 mm)

Tubes (outer diameter 30÷350 mm)

Sheets, thickness of 6; 8, 10; 15; 20; 26; 32 (370x1000 mm or 370x2000 mm)

Sheets, thickness of 24 mm (120x1000 mm or 120x2000 mm)

Details based on customer’s drawings

Granules

CAN WE HELP YOU?

If you have any questions about our products or materials or you can not find the information you are looking for, contact us via phone or email. Our team is at your disposal at any time and with pleasure.

LEARN MORE ABOUT THE SUPPORTED INDUSTRIES.