OIL & GAS INDUSTRY

 PLASTICS THAT ENDURE ALL ELEMENTS 

  • BALL VALVE SEATS

    PLASTMASS™ PEEK (Polyetheretherketone) ball valve seats are used in the oil industry at 250 °C and 160 atmospheres (at 160 °C and 320 atmospheres).

  • SEALS FOR VALVES

    PLASTMASS™ PPS (Polyphenylene sulfide) seals are suitable for valves that operate at high temperatures.

  • MOVEABLE SUPPORTS

    When laying the pipeline, the pipes are placed on special movable supports with buffer plates made of our plastics. This construction makes it possible to protect the permafrost layers from additional heat.

  • GASKETS AND BEARING BUSHINGS

    PLASTMASS™ PET (Polyethylene terephthalate) roller seals and bearing bushes ensure freely movable supports for oil and gas pipes in the temperature range from -60 ° C to +60 ° C.

  • MECHANICAL SEALS

    With the help of mechanical seals made of PLASTMASS™ PEEK VMT (Polyetheretherketone) plastics, wear was reduced and the costs for device maintenance were optimized.

  • VALVE BALLS

    Valve balls made of PLASTMASS™ PET (Polyethylene terephthalate), PLASTMASS™ PPS (Polyphenylene sulfide) and PLASTMASS™ PEI for downhole tools.

  • PADS, INSULATORS, ADAPTER & GASKET RINGS

    Pads, isolators, adapters and sealings made from PLASTMASS™ PEI and PEEK plastics are used in instruments for geophysical exploration of boreholes.

  • SENSORS, VALVES & CABLES

    Protective sensor housing, insulator parts, cable entries, valve balls made of PLASTMASS™ PPS (Polyphenylene sulfide) and PLASTMASS™ PEEK (Polyetheretherketone).

  • SLEEVES & SEALS

    We manufacture durable sleeves for submersible pumps in refineries and mechanical seals for sealed pumps in chemical factories.

  • BUSHINGS AND RINGS

    Bearing bushes, rings, liners in various pump types made from PLASTMASS™ PET (Polyethylene terephthalate), PEI (Polyetherimide) and PPS (Polyphenylene sulfide).

  • RINGS

    Our PLASTMASS™ PET (Polyethylene terephthalate) rings are used in suction rod pumps for boreholes with a high content of mechanical impurities.

  • SEALS

    PLASTMASS™ PET (Polyethylene terephthalate) labyrinth seal for engine mounts in generators.

Benefits of using Engineering Plastics & High Performance Plastics

  • Sliding properties of engineering plastics and high performance plastics are better than bronze

  • The low coefficient of friction of our plastics significantly increases the lifespan of the sliding parts

  • Engineering plastics and high performance plastics can be operated without lubrication - a failure of the lubrication system does not lead to an immediate shutdown

  • Our plastics reduce noise and increase the shock and vibration resistance of sliding units

  • Engineering plastics and high performance plastics do not require running-in due to increased elasticity

  • High positioning accuracy and freedom of movement with small feeds

  • Works in dirty conditions with high abrasion resistance

  • Not susceptible to corrosion

  • Higher chemical resistance compared to bronze

  • Moisture absorption coefficient under 0.3% 

  • High dimensional stability

  • Frost resistance at temperatures down to -100 °C

  • Consistent properties during long-term operation

We are at your disposal if you need technical advice on our materials and provide you all technical information.

CONTACT

+7 (499) 951-79-41

+7 (968) 404-13-85

English Hotline

ADDRESS

Bratislavskaya Street 6

109341 Moscow

Monday - Friday
9 am - 6 pm

Copyright © 2021 LLC, TD Plastmass Group. All Rights Reserved.